SEED STEEL!
Home > Product > Alloy structural steel

Product

Stainless steel

Special Steel

Contact us

 30CrMo Alloy Structural Steel

30CrMo Alloy Structural Steel

Grade: 30CrMo Steel
Type: steel plate, alloy structural steel, steel pipe
Standard: GB/T 3077
Specification: Thickness: 8mm--250mm||||||Width: 1500mm--4050mm ||||||Length: 3000mm to 15000mm
Application:30CrMo steel plate/sheet is used make all kinds of fasteners, high pressure pipe and more advanced carburized parts, such as gear, shaft, etc ,which work in the noncorrosive medium and temperature below 250 ℃, working with nitrogen hydrogen mixture in the medium.

30CrMo Alloy Structural Steel Introduction 

30CrMo,30CrMo Steel, Alloy Structural Steel

30CrMo Alloy Structural Steel is a kind of alloy structural steel.Its quench-hardening ability is higher, no temper brittleness.The weldability of 30CrMo Alloy Structural Steel is quite good. The tendency of cold crack formation is very small, but machinability and cold straining plasticity is good.
30CrMo Alloy Structural Steel plate/sheet is used make all kinds of fasteners, high pressure pipe and more advanced carburized parts, such as gear, shaft, etc ,which work in the noncorrosive medium and temperature below 250 ℃, working with nitrogen hydrogen mixture in the medium.
30CrMo Alloy Structural Steel Delivery state
30CrMo Alloy Structural Steel Material should be delivered at hot-rolled or hot wrought conditions. Once the demander requires(and stipulates in the contract),hot processing condition(annealing, normalizing or high-temperature backfire) can also be adopted.
30CrMo Alloy Structural Steel Application
30CrMo Alloy Structural Steel plate/sheet is used for the production of various kinds of plastic molds, such as High mirror surface mold, Mold base and so on.
 

30CrMo Alloy Structural Steel Chemical Composition Analysis  

30CrMo Chemical Composition
Grade The Element Max (%)
30CrMo C Si Mn P S
0.26-0.34 0.17-0.37 0.40-0.70 ≤0.020 ≤0.010
Cr Mo      
0.80-1.10 0.15-0.25      

30CrMo Alloy Structural Steel Mechanical Properties


Tensile Strength(σb/MPa)
Yield point(σs/MPa) Elongation(δ5/%) Reduction of Area(ψ/%) Impact Absorbing Energy(Aku2/J) Brinell Hardness(HBS100/3000)
Annealing or High Tempering
≥930 ≥785 ≥12 ≥50 ≥63 ≤229

30CrMo Alloy Structural Steel Packing

30CrMo Alloy Structural Steel Packing is normally wrapped by plastic film and waterproof paper, and then fastened on wooden pallet or as you request.

Stainless Steel Surface Finishes:

1. No 1 Finish : Used where Heat and corrsoion ressistance is required . Produced by annealing and resealing after hot rolling .

2. No 2D Finish : Dull Cold rolled finish . Used in deep drawn objects which are often polished after fabrication

3. NO 2 B Finish : Bright Cold Rolled Finish . Used in very deep drawn objects .

4. No 3 Finish : Polished finish obtained with abrasives

5. No 4 Finish : Used for kitchen ware , cooking utensils , restaurants and hotel kitchenware , cookware . Obtained with abrasives of 125 mesh and higher

6. NO 7 Finish : Architectural and Ornamental Finish

7. NO 8 Finish : Press plates , small mirrors and reflectors

8. Hairline finish : Ornamental plates , decorative items , name plates , elevators , doors in buildings

No matter what kind of steel plate you need,dont hesitate to contact us.

NAME:
E-MAIL:
TEL:
MESSAGE:
 
All World Standards Websites